Skip to content

A smartmeter project, made for ESPHome (hardware + ESPHome config)

License

Notifications You must be signed in to change notification settings

mmakaay/dsmr-reader-for-esphome

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

59 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

DSMR Reader for ESPHome

A smartmeter integration project, based on the ESP8266 D1 Mini board, made for ESPHome (hardware + ESPHome config). This device can be used with the energy dashboard that was introduced in Home Assistant 2021.8.0.

The goal of the project is to provide an open source design for an easy to build ESPHome DSMR reader device.

Made for ESPHome

PCB in enclosure

Files

Compatibility

The device can be directly powered by the smart meter. This has been tested with DSMR v4 and DSMR v5 meters.

I have a DSMR v4.2 meter myself, which delivers enough current to power the ESP8266 D1 Mini. It does require a 1000 uF capacitor though, to handle the power peaks of the D1 Mini during startup and connecting to the WiFi network.

There are also DSMR v4 meters that don't deliver enough current to run the device. For those meters and for earlier DSMR versions, it is possible to power the D1 Mini using an external power supply.

Please let me know if you find additional compatibility outcomes.

(*)Note on DSMR v4.2 without using an external power supply

The DSMR4.2 P1 port is current (up to 100 mA) AND voltage regulated (5V). The ESP8266 D1 Mini boards have short term power peaks while connecting to wifi or transmitting over wifi. With low wifi reception the peak draw can be up to 250 mA for 5-15 milisecond. This is exceeding the DSMR v4 P1 port electrical specification by far. In such cases the output voltage of the ESP8266 D1 Mini on board power regulator will drop and result in a reboot. This will happen over and over again. Increasing the capacity of the capacitor significantly can help to overcome this. Two small 6.3V 3300uF capacitors mounted in parallel instead of the 1000uF in the schematics has been implemented succesfully. These capacitors are available in Ø 10mm x 25mm and the 1000uF capacitor in the schematics can directly be substituded with one of the two. The second 3300uF capacitor can be mounted piggy-back on the other side of the PCB. The PCB does not have to be altered for this, however it will not fit the current enclosure.

2x3300uF 2x3300uF

Parts list

  • 1 x DSMR Reader PCB (can be ordered from a manufacturer like JLCPCB using the Geber file)
  • 3 x Resistor 1 kOhm
  • 1 x Resistor 200 Ohm
  • 1 x Resistor 100 Ohm
  • 1 x Transistor 2N2222 TO92
  • 1 x Optocoupler 4N35
  • 1 x Capacitor 1000 uF (ALTERNATIVE: 2 x 6.3V 3300uF Ø 10mm x 25mm, see (*)Note above)
  • 1 x RJ12 socket
  • 1 x ESP8266, D1 Mini (with male headers)
  • 2 x 8 pin female header (for connecting the D1 mini)
  • 2 x 2 pin male header
  • 2 x header jumper (fits over the 2 pin male header)
  • 1 x RJ12 to RJ12 cable (straight)

Optionally, for connecting an OLED display

  • 1 x 4 pin female shield stacking header
  • 2 x 4 pin male header (of which only the plastic part is used)
  • 1 x SSD1306 128x64 I2C OLED display

Credits

The circuit that I used as a starting point for my board: https://klushok.etv.tudelft.nl/projects/view?id=8

This one got some nice ideas too: https://willem.aandewiel.nl/index.php/2019/04/09/dsmr-logger-v4-slimme-meter-uitlezer/

This page had a good collection of info about the P1 port: http://domoticx.com/p1-poort-slimme-meter-hardware/

Some nice folks that helped me improving the design:

  • from the ESPHome discord channel, in alphabetical order: Azimath, Frank Bakker, Jos, stoic
  • Zoltán Komló

About

A smartmeter project, made for ESPHome (hardware + ESPHome config)

Resources

License

Stars

Watchers

Forks

Packages

No packages published