Releases: dirkhh/adsb-feeder-image
testbuild-g-1c179367
Full Changelog: v2.2.3-beta.1...latest
v2.2.3-beta.1
Changes since v2.2.2 include:
- update Piaware container: watchdog added for very rare TLS piaware hang; show location in FA map; faster startup of data flow in container
- fix timezone configuration for dietpi app installs
- aggregator status check: report if container down / recently started
- consistently allow spaces in sitenames (spaces replaced with underscore for MLAT name)
- radarbox: update station number when share key changes / up container version
- eliminate some minor writes from radarvirtuel, adsbhub, radar1090uk containers
Note
Based on the available usage information, I have significantly reduced the number of images provided here. If there's one that you need for a different SBC which is supported either by Armbian or DietPi, please post a request on the Zulip server
Warning
Images can take more than 5 minutes before the web interface is available. Please be patient.
Note
Currently the Odroid image and the default LePotato images do NOT support WiFi. For the default Raspberry Pi image (but not the new Raspbian image for LePotato), WiFi can be configured with the Pi Imager when you write the image to SD-card, DietPi based images do support WiFi, but they require editing two files on the DOS partition included with the image BEFORE the first boot. Please look at the adsb.im FAQ for details.
Alternatively, if there is no network connection detected, all WiFi enabled images will create a hotspot named adsb.im-feeder. You can then connect to that hotspot and set up SSID/password of the access point you want the feeder to connect to.
For Raspberry Pis there are multiple images available. For most users the Raspbian based adsb-im-raspberrypi64-pi-2-3-4-5-v....img.xz is likely the best choice, but there are also two DietPi based images available for those who prefer that.
Full Changelog: v2.2.1...v2.2.3-beta.1
v2.2.3-beta.1
Changes since v2.2.2 include:
- update Piaware container: watchdog added for very rare TLS piaware hang; show location in FA map; faster startup of data flow in container
- fix timezone configuration for dietpi app installs
- aggregator status check: report if container down / recently started
- consistently allow spaces in sitenames (spaces replaced with underscore for MLAT name)
- radarbox: update station number when share key changes / up container version
- eliminate some minor writes from radarvirtuel, adsbhub, radar1090uk containers
Note
Based on the available usage information, I have significantly reduced the number of images provided here. If there's one that you need for a different SBC which is supported either by Armbian or DietPi, please post a request on the Zulip server
Warning
Images can take more than 5 minutes before the web interface is available. Please be patient.
Note
Currently the Odroid image and the default LePotato images do NOT support WiFi. For the default Raspberry Pi image (but not the new Raspbian image for LePotato), WiFi can be configured with the Pi Imager when you write the image to SD-card, DietPi based images do support WiFi, but they require editing two files on the DOS partition included with the image BEFORE the first boot. Please look at the adsb.im FAQ for details.
Alternatively, if there is no network connection detected, all WiFi enabled images will create a hotspot named adsb.im-feeder. You can then connect to that hotspot and set up SSID/password of the access point you want the feeder to connect to.
For Raspberry Pis there are multiple images available. For most users the Raspbian based adsb-im-raspberrypi64-pi-2-3-4-5-v....img.xz is likely the best choice, but there are also two DietPi based images available for those who prefer that.
Full Changelog: v2.2.1...v2.2.3-beta.1
v2.2.2
Changes since v2.2.1 include:
- ensure remote tags are always updated - this avoids odd version number issues
Note
Based on the available usage information, I have significantly reduced the number of images provided here. If there's one that you need for a different SBC which is supported either by Armbian or DietPi, please post a request on the Zulip server
Warning
Images can take more than 5 minutes before the web interface is available. Please be patient.
Note
Currently the Odroid image and the default LePotato images do NOT support WiFi. For the default Raspberry Pi image (but not the new Raspbian image for LePotato), WiFi can be configured with the Pi Imager when you write the image to SD-card, DietPi based images do support WiFi, but they require editing two files on the DOS partition included with the image BEFORE the first boot. Please look at the adsb.im FAQ for details.
Alternatively, if there is no network connection detected, all WiFi enabled images will create a hotspot named adsb.im-feeder. You can then connect to that hotspot and set up SSID/password of the access point you want the feeder to connect to.
For Raspberry Pis there are multiple images available. For most users the Raspbian based adsb-im-raspberrypi64-pi-2-3-4-5-v....img.xz is likely the best choice, but there are also two DietPi based images available for those who prefer that.
v2.2.1
Changes since v2.2.0 include:
- raspbian image build: don't disable bluetooth via config.txt as this somehow interacts badly with pi3 mlat
- fix a couple of typos
Note
Based on the available usage information, I have significantly reduced the number of images provided here. If there's one that you need for a different SBC which is supported either by Armbian or DietPi, please post a request on the Zulip server
Warning
Images can take more than 5 minutes before the web interface is available. Please be patient.
Note
Currently the Odroid image and the default LePotato images do NOT support WiFi. For the default Raspberry Pi image (but not the new Raspbian image for LePotato), WiFi can be configured with the Pi Imager when you write the image to SD-card, DietPi based images do support WiFi, but they require editing two files on the DOS partition included with the image BEFORE the first boot. Please look at the adsb.im FAQ for details.
Alternatively, if there is no network connection detected, all WiFi enabled images will create a hotspot named adsb.im-feeder. You can then connect to that hotspot and set up SSID/password of the access point you want the feeder to connect to.
For Raspberry Pis there are multiple images available. For most users the Raspbian based adsb-im-raspberrypi64-pi-2-3-4-5-v....img.xz is likely the best choice, but there are also two DietPi based images available for those who prefer that.
v2.2.0
Changes since v2.1.6 include:
- almost all docker images have been updated since v2.1.6 (but not since the last beta). Expect a relatively slow update if coming from 2.1.7-beta.1 or earlier.
- many memory tweaks so raspbian systems with less than 4G of memory have more available
- raspbian image build: reduce gpu memory / disable bluetooth
- app install first run: fix wrong redirects
- fix stage2 local receiver with userland proxy disabled
- airspy container: avoid need for restart after hotplug
- additional aggregator links: add FlightAware and airplanes.live links
- reimplement beast and mlat status for Ultrafeeder based aggregators; this adds more status details
- don't require 1.8G of memory for stage2, only warn about recommended memory per microsite
- image: enable swap via zram
- eliminate minor disk writes by fa / fr24 containers
- disable userland proxy in the docker config for new images
- fix long load for expert page for rare circumstances
- fix tar1090 config link port when restoring app install <-> image
Note
Based on the available usage information, I have significantly reduced the number of images provided here. If there's one that you need for a different SBC which is supported either by Armbian or DietPi, please post a request on the Zulip server
Warning
Images can take more than 5 minutes before the web interface is available. Please be patient.
Note
Currently the Odroid image and the default LePotato images do NOT support WiFi. For the default Raspberry Pi image (but not the new Raspbian image for LePotato), WiFi can be configured with the Pi Imager when you write the image to SD-card, DietPi based images do support WiFi, but they require editing two files on the DOS partition included with the image BEFORE the first boot. Please look at the adsb.im FAQ for details.
Alternatively, if there is no network connection detected, all WiFi enabled images will create a hotspot named adsb.im-feeder. You can then connect to that hotspot and set up SSID/password of the access point you want the feeder to connect to.
For Raspberry Pis there are multiple images available. For most users the Raspbian based adsb-im-raspberrypi64-pi-2-3-4-5-v....img.xz is likely the best choice, but there are also two DietPi based images available for those who prefer that.
v2.1.7-beta.6
Changes since v2.1.6 include:
- up ultrafeeder version for some minor fixes
- further memory tweaks so raspbian systems with 1G/2G memory have more available
- agg status: remove api_mlat debug pring
- raspbian image build: reduce gpu memory / disable bluetooth
- app install first run: fix wrong redirects
- fix stage2 local receiver with userland proxy disabled
- airspy container: avoid need for restart after hotplug
- further memory tweaks mainly for systems with only 512 MB memory
- additional aggregator links: add FlightAware and airplanes.live links
- reimplement beast and mlat status for Ultrafeeder based aggregators; this adds more status details
- don't require 1.8G of memory for stage2, only warn about recommended memory per microsite
- image: enable swap via zram
- eliminate minor disk writes by fa / fr24 containers
- disable userland proxy in the docker config for new images
- update container versions
- fix long load for expert page for rare circumstances
- fix tar1090 config link port when restoring app install <-> image
Note
Based on the available usage information, I have significantly reduced the number of images provided here. If there's one that you need for a different SBC which is supported either by Armbian or DietPi, please post a request on the Zulip server
Warning
Images can take more than 5 minutes before the web interface is available. Please be patient.
Note
Currently the Odroid image and the default LePotato images do NOT support WiFi. For the default Raspberry Pi image (but not the new Raspbian image for LePotato), WiFi can be configured with the Pi Imager when you write the image to SD-card, DietPi based images do support WiFi, but they require editing two files on the DOS partition included with the image BEFORE the first boot. Please look at the adsb.im FAQ for details.
Alternatively, if there is no network connection detected, all WiFi enabled images will create a hotspot named adsb.im-feeder. You can then connect to that hotspot and set up SSID/password of the access point you want the feeder to connect to.
For Raspberry Pis there are multiple images available. For most users the Raspbian based adsb-im-raspberrypi64-pi-2-3-4-5-v....img.xz is likely the best choice, but there are also two DietPi based images available for those who prefer that.
v2.1.7-beta.5
Changes since v2.1.6 include:
- app install first run: fix wrong redirects
- fix stage2 local receiver with userland proxy disabled
- airspy container: avoid need for restart after hotplug
- further memory tweaks mainly for systems with only 512 MB memory
- additional aggregator links: add FlightAware and airplanes.live links
- reimplement beast and mlat status for Ultrafeeder based aggregators; this adds more status details
- don't require 1.8G of memory for stage2, only warn about recommended memory per microsite
- image: enable swap via zram
- eliminate minor disk writes by fa / fr24 containers
- disable userland proxy in the docker config for new images
- update container versions
- fix long load for expert page for rare circumstances
- fix tar1090 config link port when restoring app install <-> image
Note
Based on the available usage information, I have significantly reduced the number of images provided here. If there's one that you need for a different SBC which is supported either by Armbian or DietPi, please post a request on the Zulip server
Warning
Images can take more than 5 minutes before the web interface is available. Please be patient.
Note
Currently the Odroid image and the default LePotato images do NOT support WiFi. For the default Raspberry Pi image (but not the new Raspbian image for LePotato), WiFi can be configured with the Pi Imager when you write the image to SD-card, DietPi based images do support WiFi, but they require editing two files on the DOS partition included with the image BEFORE the first boot. Please look at the adsb.im FAQ for details.
Alternatively, if there is no network connection detected, all WiFi enabled images will create a hotspot named adsb.im-feeder. You can then connect to that hotspot and set up SSID/password of the access point you want the feeder to connect to.
For Raspberry Pis there are multiple images available. For most users the Raspbian based adsb-im-raspberrypi64-pi-2-3-4-5-v....img.xz is likely the best choice, but there are also two DietPi based images available for those who prefer that.
v2.1.7-beta.4
Changes since v2.1.6 include:
- airspy container: avoid need for restart after hotplug
- further memory tweaks mainly for systems with only 512 MB memory
- additional aggregator links: add FlightAware and airplanes.live links
- reimplement beast and mlat status for Ultrafeeder based aggregators; this adds more status details
- don't require 1.8G of memory for stage2, only warn about recommended memory per microsite
- image: enable swap via zram
- eliminate minor disk writes by fa / fr24 containers
- disable userland proxy in the docker config for new images
- update container versions
- fix long load for expert page for rare circumstances
- fix tar1090 config link port when restoring app install <-> image
Note
Based on the available usage information, I have significantly reduced the number of images provided here. If there's one that you need for a different SBC which is supported either by Armbian or DietPi, please post a request on the Zulip server
Warning
Images can take more than 5 minutes before the web interface is available. Please be patient.
Note
Currently the Odroid image and the default LePotato images do NOT support WiFi. For the default Raspberry Pi image (but not the new Raspbian image for LePotato), WiFi can be configured with the Pi Imager when you write the image to SD-card, DietPi based images do support WiFi, but they require editing two files on the DOS partition included with the image BEFORE the first boot. Please look at the adsb.im FAQ for details.
Alternatively, if there is no network connection detected, all WiFi enabled images will create a hotspot named adsb.im-feeder. You can then connect to that hotspot and set up SSID/password of the access point you want the feeder to connect to.
For Raspberry Pis there are multiple images available. For most users the Raspbian based adsb-im-raspberrypi64-pi-2-3-4-5-v....img.xz is likely the best choice, but there are also two DietPi based images available for those who prefer that.
v2.1.7-beta.3
Changes since v2.1.6 include:
- further memory tweaks mainly for systems with only 512 MB memory
- additional aggregator links: add FlightAware and airplanes.live links
- reimplement beast and mlat status for Ultrafeeder based aggregators; this adds more status details
- don't require 1.8G of memory for stage2, only warn about recommended memory per microsite
- image: enable swap via zram
- eliminate minor disk writes by fa / fr24 containers
- disable userland proxy in the docker config for new images
- update container versions
- fix long load for expert page for rare circumstances
- fix tar1090 config link port when restoring app install <-> image
Note
Based on the available usage information, I have significantly reduced the number of images provided here. If there's one that you need for a different SBC which is supported either by Armbian or DietPi, please post a request on the Zulip server
Warning
Images can take more than 5 minutes before the web interface is available. Please be patient.
Note
Currently the Odroid image and the default LePotato images do NOT support WiFi. For the default Raspberry Pi image (but not the new Raspbian image for LePotato), WiFi can be configured with the Pi Imager when you write the image to SD-card, DietPi based images do support WiFi, but they require editing two files on the DOS partition included with the image BEFORE the first boot. Please look at the adsb.im FAQ for details.
Alternatively, if there is no network connection detected, all WiFi enabled images will create a hotspot named adsb.im-feeder. You can then connect to that hotspot and set up SSID/password of the access point you want the feeder to connect to.
For Raspberry Pis there are multiple images available. For most users the Raspbian based adsb-im-raspberrypi64-pi-2-3-4-5-v....img.xz is likely the best choice, but there are also two DietPi based images available for those who prefer that.