bring up to date

config/examples/Printrbot/Simple_Metal_RevF6/Configuration.h

@@ -108,7 +108,7 @@
 
 /**
  * Select a third serial port on the board to use for communication with the host.
- * Currently only supported for AVR, DUE, LPC1768/9 and STM32/STM32F1
+ * Currently supported for AVR, DUE, SAMD51, LPC1768/9, STM32/STM32F1/HC32, and Teensy 4.x
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7, 8, 9]
  */
 //#define SERIAL_PORT_3 1
@@ -387,14 +387,15 @@
  * PRUSA_MMU1 : Průša MMU1 (The "multiplexer" version)
  * PRUSA_MMU2 : Průša MMU2
  * PRUSA_MMU2S : Průša MMU2S (Requires MK3S extruder with motion sensor, EXTRUDERS = 5)
+ * PRUSA_MMU3 : Průša MMU3 (Requires MK3S extruder with motion sensor and MMU firmware version 3.x.x, EXTRUDERS = 5)
  * EXTENDABLE_EMU_MMU2 : MMU with configurable number of filaments (ERCF, SMuFF or similar with Průša MMU2 compatible firmware)
  * EXTENDABLE_EMU_MMU2S : MMUS with configurable number of filaments (ERCF, SMuFF or similar with Průša MMU2 compatible firmware)
  *
  * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
  * See additional options in Configuration_adv.h.
- * :["PRUSA_MMU1", "PRUSA_MMU2", "PRUSA_MMU2S", "EXTENDABLE_EMU_MMU2", "EXTENDABLE_EMU_MMU2S"]
+ * :["PRUSA_MMU1", "PRUSA_MMU2", "PRUSA_MMU2S", "PRUSA_MMU3", "EXTENDABLE_EMU_MMU2", "EXTENDABLE_EMU_MMU2S"]
  */
-//#define MMU_MODEL PRUSA_MMU2
+//#define MMU_MODEL PRUSA_MMU3
 
 // @section psu control
 
@@ -1477,7 +1478,8 @@
  * A lightweight, solenoid-driven probe.
  * For information about this sensor https://github.com/bigtreetech/MicroProbe
  *
- * Also requires: PROBE_ENABLE_DISABLE
+ * Also requires PROBE_ENABLE_DISABLE
+ * With FT_MOTION requires ENDSTOP_INTERRUPTS_FEATURE
  */
 //#define BIQU_MICROPROBE_V1 // Triggers HIGH
 //#define BIQU_MICROPROBE_V2 // Triggers LOW
@@ -1647,6 +1649,7 @@
  #define PROBE_TARE_DELAY 200 // (ms) Delay after tare before
  #define PROBE_TARE_STATE HIGH // State to write pin for tare
  //#define PROBE_TARE_PIN PA5 // Override default pin
+ //#define PROBE_TARE_MENU // Display a menu item to tare the probe
  #if ENABLED(PROBE_ACTIVATION_SWITCH)
  //#define PROBE_TARE_ONLY_WHILE_INACTIVE // Fail to tare/probe if PROBE_ACTIVATION_SWITCH is active
  #endif
@@ -1684,8 +1687,8 @@
  * probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
  * Only integer values >= 1 are valid here.
  *
- * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
- * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
+ * Example: 'M851 Z-5' with a CLEARANCE of 4 => 9mm from bed to nozzle.
+ * But: 'M851 Z+1' with a CLEARANCE of 2 => 2mm from bed to nozzle.
  */
 #define Z_CLEARANCE_DEPLOY_PROBE 4 // (mm) Z Clearance for Deploy/Stow
 #define Z_CLEARANCE_BETWEEN_PROBES 3 // (mm) Z Clearance between probe points