You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
This summer, I ordered 10-15 dimmers from Namron. Initially, I received only 4 devices, with the remaining ones arriving in October. The first batch, which came with firmware version 3.09, performed flawlessly—allowing me to turn the lights on and off and adjust the brightness with immediate response. However, the final batch arrived with firmware version 3.10, which caused issues. The lights would take a few seconds to turn on, and after about 10-15 seconds, I encountered an error in Z2M. So if i turned on the light it would turn on and after about 10-15 sec i get the error message. If I in the same timespan (before the error) I try to adjust the brightness nothing happens until the first error shows up. After the error shows it will then adjust the brightness and 10-15 sec later it will show a new error message.
So all the new dimmers with the 3.10 firmware have this issue that turning them on or off works but after 10-15 sec we get an error message. It also looks like no other commands in the 10-15 sec are processed until the error message is displayed.
After contacting the distributor in Norway about the difference in the firmware, I got this response back (from device manufacture in china):
Changes v3.09 > v3.10
Implementation of Min, Max and start-up level of lightness.
Clusters for dimmer settings Min,Max, Start-Up light levels
Implement in the dimmer fw in the dimmer MCU the chosen ZB Clusters respectively:
(The chosen ZB Cluster is from the zigbee standard for Ballast, not Light control. Since there is no defined ZB Cluster for these settings in the ZB standard library)
Cluster 0x301 (Ballast Configuration)
Attribute 0x001 (Ballast settings)
Attributes set 0x0010 (Min level setting) (6 repeated short push on the self reset switch)
0x0011 (Max level setting) (8 repeated short push on the self reset switch)
0x0012 (Power On level) (5 repeated short push on the self reset switch)
These chosen attributes may be implemented in the ZB instructions in the MCU.
We think it can be tested by sending commands to the UART Interface on the CPU ( RX/TX) directly via cable.
Because we still don’t have any App to test on. It will be available in September.
What did you expect to happen?
I expected that they would respond the same as the other devices with the 3.09 firmware
How to reproduce it (minimal and precise)
Toggle the light on/off and check the error logs about 10-20 seconds after changing the dimmer's state.
What happened?
This summer, I ordered 10-15 dimmers from Namron. Initially, I received only 4 devices, with the remaining ones arriving in October. The first batch, which came with firmware version 3.09, performed flawlessly—allowing me to turn the lights on and off and adjust the brightness with immediate response. However, the final batch arrived with firmware version 3.10, which caused issues. The lights would take a few seconds to turn on, and after about 10-15 seconds, I encountered an error in Z2M. So if i turned on the light it would turn on and after about 10-15 sec i get the error message. If I in the same timespan (before the error) I try to adjust the brightness nothing happens until the first error shows up. After the error shows it will then adjust the brightness and 10-15 sec later it will show a new error message.
Turning the light ON
Dimming the light
Turning the light OFF
So all the new dimmers with the
3.10
firmware have this issue that turning them on or off works but after 10-15 sec we get an error message. It also looks like no other commands in the 10-15 sec are processed until the error message is displayed.After contacting the distributor in Norway about the difference in the firmware, I got this response back (from device manufacture in china):
What did you expect to happen?
I expected that they would respond the same as the other devices with the
3.09
firmwareHow to reproduce it (minimal and precise)
Toggle the light on/off and check the error logs about 10-20 seconds after changing the dimmer's state.
Zigbee2MQTT version
1.40.2
Adapter firmware version
20210708
Adapter
Sonoff Zigbee 3.0 USB Dongle
Setup
add-on on Home Assistant
Debug log
The text was updated successfully, but these errors were encountered: